Best gyro sensitivity settings for BGMI, and how to tune them

Gyroscope aiming is the single biggest skill jump most BGMI players can make, and it lives or dies on your gyro sensitivity. Set it too low and your aim feels like it is dragging through mud; set it too high and a small tilt sends your crosshair flying off the target. The right gyro sensitivity for BGMI sits in a narrow band, and this guide gives you tested starting values for every scope, explains what each number does, and shows how to fine-tune them so you can actually hold a spray on a moving enemy.

One thing to be clear about first. There is no secret code that gives you zero recoil or an auto lock. Gyro control comes from settings that suit your device plus a couple of weeks of muscle memory. The values below are a strong baseline, not magic.

Best gyro sensitivity settings for BGMI (starting values)

These are balanced starting numbers for a mid to high-end phone. Apply them to the Gyroscope Sensitivity section, and use the same values in the ADS Gyroscope Sensitivity section, which is the one that fights recoil while you are actually firing. They lean toward control rather than raw speed, which is what you want when you are learning to spray with the gyro. Keep every gyro value under 400, since higher than that makes the aim twitchy and unstable on most devices.

Scope	Gyroscope sensitivity
TPP / FPP no scope	300%
Red dot, holo, aim assist	300%
2x scope	250%
3x scope	200%
4x scope (VSS, SLR)	150%
6x scope	100%
8x scope	70%

Notice the pattern. Close-range scopes get high sensitivity because you need to swing fast onto a target at short distance, and long-range scopes get low sensitivity because a small tilt already moves the crosshair a long way when you are zoomed in. If your 8x feels impossible to steady while sniping, drop it to 60 before you touch anything else.

What gyro sensitivity actually controls

Gyroscope sensitivity decides how much your view turns for a given tilt of the phone. It is separate from Camera and ADS sensitivity, which respond to your thumb swipes on the screen. BGMI actually splits the gyro into two sliders: Gyroscope Sensitivity governs your general tilt aim, and ADS Gyroscope Sensitivity only kicks in while you are shooting, which makes it the one doing the real recoil control. Tilting the device down and left counters the upward-right pull of a rifle’s kick, which is why gyro players can hold long sprays that would be almost impossible with thumb aim alone.

Because it reacts to physical movement, the same code feels different on every phone. A flagship reading the sensor at a high refresh rate registers your tilt faster than a budget device, so a value that feels smooth on one handset can feel sluggish or jumpy on another. That is the reason no single shared code is right for everyone, and it is why the tuning step below matters more than the starting numbers.

Scope On or Always On: which gyro mode to use

BGMI gives you three gyroscope modes in the settings. Off disables it entirely. Scope On activates the gyro only while you are aiming down sights, so your normal movement stays on thumb controls. Always On keeps the gyro live the whole time, including hip fire and free look.

If you are new to the gyro, start with Scope On. It lets you learn tilt control in the one situation that rewards it most, holding a spray during a fight, without fighting the phone while you are just running around. Once that feels natural, usually after two to three weeks, switch to Always On. Nearly every high-level player uses Always On because it removes the delay of the gyro switching on the instant you aim, and it lets you make tiny corrections during close hip-fire scraps.

How to change gyro sensitivity in BGMI

Applying new values takes about a minute:

1. Open BGMI and tap the arrow icon in the bottom-right corner of the lobby screen, then open Settings.
2. Go to the Sensitivity tab and scroll to the Gyroscope Sensitivity and ADS Gyroscope Sensitivity sections.
3. Set your gyro mode to Scope On or Always On at the top of the sensitivity page.
4. Enter the values from the table above for each scope, or import a code through the sensitivity code option and confirm.
5. Save, then head straight to the Training Ground to test before you queue a match.

If you are importing a shared code rather than typing values, treat it exactly the same way. A code is just a bundle of numbers, so it still needs testing on your device before it means anything in a ranked lobby.

How to tune your gyro sensitivity the right way

The starting table gets you close. The last ten per cent, the part that decides whether you win close fights, comes from testing. Here is the method the good players use.

Go into the Training Ground and pick up an M416 with no attachments except a scope. Aim at a wall from a fixed distance and hold the trigger for a full magazine while using the gyro to keep the crosshair pinned on one spot. Watch where the bullets climb. If your aim drifts up and to the right and you cannot pull it back down, your gyro value for that scope is too low, so raise it by 10 to 20 points. If the crosshair overshoots and jitters past your target with the smallest tilt, the value is too high, so lower it by the same amount.

Change one scope at a time and only in small steps. The most common mistake is importing a fresh code and jumping into a ranked match with it, then blaming the code when the real problem is that your hands have not adjusted. Give any new setup at least a few days of matches before you decide it does not work.

Common gyro sensitivity mistakes to avoid

Three errors hold most players back. The first is chasing a “best” code from a random site and expecting instant results, when the number that matters is the one your own hands are trained on. The second is setting gyro values above 400 in the hope of faster aim, which almost always produces shaky, uncontrollable movement. The third is switching settings every single day, which resets your muscle memory before it can form. Pick a sensible baseline, tune it once, then leave it alone and put your time into playing.

Grip helps too. Gyro control is smoother when you can tilt the phone freely, so a two-thumb grip with the device held slightly away from your body gives you more range of motion than clutching it tight against your palms.

What is the best gyro sensitivity code for BGMI?

There is no universal best code, and any site promising one that delivers instant no recoil is overselling it. The closest thing to a best code is a balanced baseline like the table above, imported and then tuned to your own phone in the Training Ground. A code that a pro streamer swears by can feel terrible on your device because their handset reads the gyro sensor differently. Use codes as a starting point, never as a finished answer.

Is gyro better than non-gyro in BGMI?

For controlling recoil at range, gyro is clearly stronger, which is why almost every competitive player uses it. Tilting the phone to counter the gun’s kick lets you hold sprays that thumb aim struggles with, especially through a 3x or 4x. The trade-off is the learning curve, since it takes a few weeks to feel natural. If you play seriously and want to climb ranks, the time spent switching to gyro pays off. If you only play casually, non-gyro is fine and less demanding.

If you want to go deeper on the thumb-aim side of your setup, our full breakdown of BGMI sensitivity settings and no-recoil codes covers Camera and ADS values, and our guide to BGMI control codes and claw layouts shows how to arrange your buttons so the gyro and your fingers work together.

Gyro aiming feels awkward for the first week and then it clicks, and once it does you will not want to play without it. Start with the values here, commit to Scope On before you graduate to Always On, and let the Training Ground do the fine-tuning.

Explore more BGMI guides and esports features